Victron Phoenix Smart 12/30/3 12V 30A 3 output IP43 Battery Charger

Victron Energy Phoenix Smart 12/30/3 12V 30A 3 output IP43 Battery Charger

With boat owners in mind this adaptive 5-step charger can provide either 30A or 50A of charge to each of three battery banks. Or the charger 1+1 model provides 3A to the starter-battery, the rest to the ‘house’ bank. 24V models are available with 16A/25A charge. Bluetooth enabled, you can monitor the charger and set alarms straight from your phone. Adaptive, intelligent, dynamic charge features – see the datasheet below.
Bluetooth Smart built-in
The wireless solution to set-up, monitor, control and update Smart IP43 Chargers.
Smart IP43 Charger (3): three full current outputs to charge 3 battery banks
Each output can supply the full rated output current. But the total of the 3 outputs combined can never exceed the current rating of the charger.
Automatic voltage compensation
The charger compensates for voltage drop over the DC cabling by slightly increasing output voltage when the DC current increases. Please see the manual for details.
Adaptive 6-stage charge algorithm: bulk– absorption – recondition – float – storage – refresh
The Smart IP43 Charger features our well-known ‘adaptive’ battery management system that can be preset to suit different types of batteries. The ‘adaptive’ feature will automatically optimise the charge process relative to the way the battery is being used.
The right amount of charge: variable absorption time
When only shallow discharges occur (a yacht connected to shore power for example) the absorption time is kept short in order to prevent overcharging of the battery. After a deep discharge the absorption time is automatically increased to make sure that the battery will be fully charged.
Preventing damage due to excessive gassing: the BatterySafe mode (see fig. 2)
If, in order to quickly charge a battery, a high charge current in combination with a high absorption voltage has been chosen, the charger will prevent damage due to excessive gassing by automatically limiting the rate of voltage increase once the gassing voltage has been reached (see the charge curve between 14,4 V and 15,0 V in fig. 2).
Less maintenance and aging when the battery is not in use: the Storage Mode (see fig. 1 & 2)
The Storage Mode kicks in whenever the battery has not been subjected to discharge during 24 hours. In the Storage Mode float voltage is reduced to 2,2 V/cell (13,2 V for a 12 V battery) to minimise gassing and corrosion of the positive plates. Once a week the voltage is raised back to the absorption level to ‘equalize’ the battery. This feature prevents stratification of the electrolyte and sulphation, a major cause of early battery failure.
Also charges Li-ion (LiFePO₄) batteries
Charger on-off control can be implemented by connecting a relay or open collector optocoupler output from a Li-ion BMS to the remote on/off port. Alternatively full control of voltage and current can be achieved with Bluetooth.
Fully programmable charge algorithm
The charge algorithm can be programmed with help of Bluetooth or the VE.Direct interface. Three preprogrammed algorithms can be selected with the mode button (see specifications).
Optional external battery voltage and temperature sensing via Bluetooth
A Smart Battery Sense, SmartShunt or a BMV-712 Smart Battery Monitor can be used to communicate battery voltage and temperature to one or more Smart IP43 Chargers via VE.Smart Networking.
Remote on/off
The remote on/off consists of two terminals: Remote H and Remote L. A remote on/off switch or relay contact can be connected between H and L. Alternatively, terminal H can be pulled high, or terminal L can be pulled low. See the manual for details.
VE.Direct interface
For a wired data connection to a GX device such as the Cerbo GX, PC or other devices. Also enables Instant Readout functionality via VictronConnect remotely from VRM. Please see the VictronConnect app.
Programmable relay
Can be programmed using the VE.Direct interface or a Bluetooth enabled device to trip on an alarm or other events.

Specifications:
Model: Phoenix Smart 12/30/3;
Input voltage: 230VAC (range: 210 – 250V);
DC input voltage range: 290 – 355 VDC;
Frequency: 45 - 65 Hz;
Power Factor: 0.7;
Current losses:
- AC disconnected: < 0.1 mA;
- AC connected and off remote charger: <6 mA;
No-load power consumption: 1W;
Efficiency: 94%;
Charging voltage - Absorption/Maintenance/Accumulation:
- Normal: 14,4 V/13,8 V/13,2 V
- High: 14,7 V/13,8 V/13,2 V
- Li-ion: 14,2 V/n/a/13,5 V
Fully programmable: Yes, via Bluetooth and/or VE.Direct;
Number of battery connections: 3;
Corr. service battery charge: 30/50 A;
Low Current Mode: 15/25A;
Temperature Compensation - Default: -16 mV/°C;
Charge current starter battery: 3 A (only models with 1+1 output);
Charge algorithm: 6-stage adaptive (3-stage for lithium-ion);
Protection: Battery reverse polarity (fuse not accessible to user) / Output short circuit / Overtemperature;
Can be used as a power supply: Yes, the output voltage can be set via Bluetooth and/or VE.Direct;
Operating temperature range: -20 to 60°C (0 to 140°F) - Rated output current up to 40°C, linear reduction up to 20% at 60°C;
Humidity (non-condensing): max 95%;
Remote on/off: Yes (bipolar terminal);
Relay (Programmable): Rated DC: 5A up to 28VDC;
Bluetooth: Power: -4 dBm | Frequency: 2402 - 2480 MHz.
CARCASS
Material and colour: aluminum (blue RAL 5012);
Battery connection: Screw terminals 16 mm² (AWG6);
AC connection: IEC 320 C14 input with clamp (the AC cable with specific ground plug must be requested separately);
Protection category: IP43 (electronic components), IP22 (connection area);
Weight: 3.5 kg;
Dimensions (HxWxD): 180x249x100 mm;
REGULATIONS
Safety: EN 60335-1, EN 60335-2-29;
Emissions: EN 55014-1, EN 61000-6-3, EN 61000-3-2;
Immunity: EN 55014-2, EN 61000-6-1, EN 61000-6-2, EN 61000-3-3;
Vibration: IEC68-2-6:10-150Hz/1.0G.

For further information, consult the technical datasheet or looking images.